japanese乱熟另类,国产精品久久久久久人妻精品,xxxxxhd亚洲日本hd

TranslationMobile

最大壓力
最大應力

"maximum" in Chinese : n. (pl. maximums, -ma ) 極點，最 ...
"stress" in Chinese : n. 1.壓力，壓迫，緊迫，緊張。 2.【語音】重音；重 ...
"stress maximum" in Chinese : 應力峰值
"absolute maximum shear stress" in Chinese : 所有方向上最大剪應力
"allowable maximum service stress" in Chinese : 許用最大工作應力
"direction of maximum shear stress" in Chinese : 最大剪應力方向
"direction of the maximum stress" in Chinese : 最大應力方向
"limiting maximum stress" in Chinese : 極限最大應力
"magnitude of maximum shearing stress" in Chinese : 最大剪應力值
"maximum allowable stress value" in Chinese : 最大允許應力值
"maximum crushing stress" in Chinese : 最大壓應力
"maximum cyclic stress" in Chinese : 最大循環負荷; 最大循環應力
"maximum fiber stress" in Chinese : 最大纖維應力
"maximum fibre stress" in Chinese : 最大纖維應力
"maximum normal stress" in Chinese : 最大法向應力

Examples

Maximum stress theory
最大應力理論
Because of high sharp peak , vibration stress is big , and the maximum stress achieves 550mpa
由于油缸沖擊載荷有比較大的峰值，泵車動應力比較大，最大值達到550mpa 。
The result indicates that the maximum stress on the runner is mainly in proportion to the turbine output
結果表明在大部分工況下該轉輪葉片最大靜應力基本上與水輪機功率成線性關系。
The maximum stress was on the apices and the stress on the cervical part was lower
種植體應力主要為均勻分布的壓應力，最大應力位于種植體根尖部，頸部應力相對較小，未見明顯彎曲應力。
The mechanical simulation compared the stress distribution in copper lines and pore , with the result that the maximum stress locates in the corner
在力學模擬過程中，計算了銅互連線和通孔的熱應力的分布。
The results are that the maximum displacement and maximum stress occurs at initial time and the maximum stress is less than permissible stress
結果表明,結構最大應力和最大位移均發生在初始時刻,最大應力小于許用應力。
By analyzing the optimal diffluent ratio and solder angle of the dies , the maximum stress in the body of improved dies is de - creased effectively
對模具的分流比和焊合角進行優化并再次模擬，發現分流模的最大應力大大降低。
The stress of horizontal working states is bigger than others , and the maximum stress attaches to 540 mpa . only considering static strength , the bump auto satisfies command
水平工況應力較大，最大應力為540mpa ，單從靜強度方面考慮，該泵車滿足強度要求。
Using the library functions of msc . patran language the stresses of structural elements is picked up , and the maximum stress of the elements controlled by the same design variable is found
利用msc . patran的庫函數，提取結構單元的節點應力，通過循環找到構件的最大應力。
2 the maximum stress and the maximum stress location and the distribution of the stress are attained through the static analysis of building up finite element module
2 、對建立的有限元模型進行靜強度分析，得到各個工況該泵車的最大靜應力值和最大靜應力位置及各構件的靜應力分布。